3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
"You need to buy this special heater pad to break the screen adhesive!"
No, I think you will find that in fact I don't.
Holy shit. I do a fair bit of small electronics repair on the side, the cost of a decent heat pad is about half that of a 3d printer... This may be what finally inspires me to get a 3d printer.
Can I use it to warm up a sex toy? Asking for me.
Just 3d print one and grab it while it's fresh and warm.
I realize this is a joke…
But don’t do this. Really. The fdm layers are unhygienic, and there’s a not-insignificant risk of things snapping off and leading to awkward emergency room visits.
A better solution is printing a 2 part mold and casting silicone.
glad to hear from the 3d printed sex toy experts in the house
wont the layers transfer to the silicone?
You can process the inside to be smooth (sanding, priming. If you have a solvent - acetone for abs, as an example. And mold release.)
Even just using a filler/primer should be enough
Aren’t ribs a good thing sometimes?
I was really impressed by the lulzbot manual mentioning this! Its also important to consider that most 3d prints can be sensitive to water unless sealed too.
I’m just gonna assume some one printed a butplug, had it snap off leading to said emergency room visit and they tried to sue lulzbot.
Who is this someone you're talking about, FuglyDuck ?
Sadly not.
I was told. Without asking. By a long lost friend of a cousin you wouldn't know.
My sex toy goes to a different school
Ngl that's fucking genius
Seeing as you can do the exact same thing with a hairdryer, it's inventing a solution to a problem that doesn't exist.
The heated bed is coupled to a thermistor. I'd argue controlling the temperature in order to not accidentally overheat parts of the phone is a step above a hair dryer.
Also bad is that hair dryers don't spread their heat around very well at all. You can easily create hotspots on the object and damage things with them.
And, I don't own a hairdryer. (Or much in the way of hair, these days.) But I do own a 3D printer...
Has anyone else found a use for their 3D printer that wasn't exactly listed on the label?
Not from the 3D printing world, but sometimes I'd use our heating plate to reheat pizza LOL! Gotta make sure to clean the surface really well afterwards though.
Sounds like a job for tin foil or parchment paper
This is an amazing tip tbh. Never thought of using it for that.
Doesn't that require a much higher temperature than most beds would be able to safely achieve.
I had to take the screen off of a Pixel not terribly long ago to replace the battery. I used a heat gun and I remember it requiring a temperature of like... 240C° or some such? And when I'm printing PLA, my printer bed only gets to 60C°. (Not saying it couldn't go higher, but 240C° seems way higher than 60C°.)
No, that temperature would damage your screen. The professional hot plates for phone repair are typically set to 85-90°C. With a heat gun you may need to set a higher temperature since you are only heating up part of the phone and it cools down again during the process. My printer (Prusa MK3) with PCB heater can go up to 120°C, so it looks perfect for the job.