No Stupid Questions

Smart bulbs like this:

Have PCBs with small LEDs surface mounted to them. This means that the on-off cycle of the bulb causes heat deformation cycles of the PCB. This stresses the foils in the PCB and can eventually cause them to lose connection. That’s one of the reasons why they’ll often start flickering or lose the ability to be cool white, warm white, or specific colors (the different kinds of LEDs in them).

But bulbs like this (often called smart edison bulbs):

Use longer/larger LEDs that aren’t mounted to the PCBs, and will probably last much longer. They are better at not overheating their own electronics.

If you want the first kind to last longer, don’t run them above ~60% brightness.

They don’t? What are you talking about?

Only buy Philips (not the Hue stuff) or Osram

The rest are shite

My smart LED bulbs don't even say how long they last, but my experience with LEDs in general tells me they will last practically forever. Out of all the LED things I have, the only ones with any burnt out lights are a couple of cheap LED strips I have and I can't even be sure the ones that are dead weren't because of where I cut the strip. I've had those things for over 12 years now and they're in my PC which is always on.

Afaik, the biggest threat to killing the LED is heat, and some cheaper LED bulbs have really poor heat dissipation. Technology Connections has a video about them, which may be more informative.

FWIW, I've killed a bunch of Phillips hue bulbs through normal use

i have 7 bulbs since 2019
none of them failed so far.

all the lifespans i found ranged between 15.000 to 25.000 hours ( which btw was equated to 1.000 hours per year instead of 5.000 per year)

so this doesn't sound normal to me.

how manny(in use) bulbs do you have?
what brands do you use?

I have a dozen that run 12+ hours a day. I've had 1 fail in 5 years.

Don't buy cheap LEDs, and don't put them in enclosures that trap heat.

Get the ones with the strip LEDs that look like they're trying to emulate a glowing tungsten filament. I can't remember where I got the information; it was like the Technology Connections YouTube channel or something, but I remember them saying that since they put the LED lights in series on those bulbs, they have a much higher voltage requirement to drive them, and much less circuitry is needed. It's the circuitry that burns out, and many of these filament-style LED lights literally only have a resistor as their main component.

I've swapped to these kinds of LEDs like...5 years ago, and haven't had one burn out yet. Probably have like...15 of them across the entire house.

https://youtu.be/fsIFxyOLJXM?si=4wz0wa355Wd9gkUP&t=1389 -- YEP -- Found the advice. Starts at 23:09 BigCliveDotCom also says the same in his episode about Dubai Lamps: https://www.youtube.com/watch?v=klaJqofCsu4

Heat.

While the actual LEDs (*) may be rated up to 20,000 hours+ in optimum circumstances, but the actual 3rd party bulb manufacturers, especially the cheapo brands, are building bulbs with poor heat dissipation designs and cheap and/or poorly designed circuits. Same goes for other parts they may use, such as the power supply. To reach 20,000+ hours, you need everything - not just the LED - to be working optimally together.

(*) the best LED makers out there right now, e.g. Nichia, Cree, Phillips - really do some amazing engineering.

The same reason that western countries refused to buy the extremely hard to break Superfest glasses manufactured in the GDR (East Germany) during the Cold War: planned obsolescence and consumable goods mentality in the interest of profit (they got a west German salesman to take the glasses to a trade show, and nobody gave a shit, because part of the industry’s profit model at the time was the sale of new glass due to breakage.

In point of fact: better, longer lasting LED bulbs DO exist, but they’re only sold in Dubai (due to the monarchy there basically decreeing that they wanted that to happen, so Phillips made them for them, but will NOT sell them outside of the country, because it would kill their sales elsewhere).

Generally because you're buying cheaper ones that aren't built as well. Heat destroys LEDs and the cheap bulbs generally use fewer individual LEDs running at higher power to produce a given output in lumens. More expensive bulbs use more LEDs at lower power to achieve the same light output so that they're not constantly being overdriven and last much longer.

They've been sabotaged by design. LEDs should last 10+ years if built even half away reasonably, but unfortunately the manufacturers basically got together and agreed to build them in such a way they would fail. Same as regular light bulbs, they just have to work harder.

I still have some of the earliest modern LED bulbs on the market--old Philips ones, the AmbientLED (i think) with the yellow casing and large heat sinks. They've been running for like 15 years now and not a one of them has failed. I spent several hundred USD replacing all my bulbs with those back in the day and they've done me well.

Modern bulbs are trash by comparison. Not because the technology is limited in some way but because they refuse to make anything to that quality anymore.

We need an alternate solution to this planned obsolescence bullshit. Light bulbs hit 50k rated hours long ago and they were talking about making ones that went 100k+ but these days you can't find anything above 25k. And that's setting aside the fact that a lot of these rely on apps that could be dropped at a moment's notice.

Typically it's not the emitters -- the LED's themselves -- that fail. If driven correctly, those have lifetimes of tens of thousands of hours. That's what the manufacturer is advertising on the box. Yes, an individual LED when driven correctly will probably last 20,000 hours. (Usually more, depending on how pedantic you want to get. The 20,000 hour figure often quoted is the point where the emitter drops to 80% of its original light output.)

LED "bulbs," the type that replace filament bulbs in consumer fixtures, typically fail in their driver hardware. LED's run off of low voltage DC and in the base of all of those LED conversion bulbs is a power conversion assembly that steps down and rectifies 120v/240c AC to whatever DC voltage the LED array in there expects. These are inevitably made out of whatever the cheapest passives and semiconductor components the manufacturer thinks they can get away with. These don't last 20,000 hours, especially not in where they're usually installed.

The main killer for all semiconductor electronics, which includes both LED's themselves and their driver circuitry, is heat. This is often exacerbated by the fact that LED replacement modules are usually stuck in enclosed light fixtures designed for filament bulbs that have insufficient ventilation to get rid of the waste heat from the components in an LED module. The insides of those enclosed ceiling light fixtures, the ubiquitous "boob light," gets hot, even with only LED modules installed. Filament bulbs don't care because they don't have any electronics in them and how they work is literally by getting so hot the glow. But LED modules in that kind of environment will invariably suffer an early failure.

The best way you can get your LED modules to last longer is to install them in a fixture where they'll have a lot of air circulation available or at the very least which is not fully enclosed.

The bulbs themselves are amazing. There are good ones in cars and computers, the flash of phones etc.

The failure point is typically the electronic components that run or regulate it. And of course most companies want to sell more bulbs so they conveniently skimp on that stuff. So maybe the answer is a more expensive bulb that hopefully will last long enough to justify the extra cost?

What would you recommend?

Philips.

My experience has been that they last for more years than I tend to notice which ones are which. I'm not mad at all about their longevity.

I had 2 LED bulbs that I know for sure that I bought prior to 2015 that only recently failed. Those bulbs lasted at least 9-10 years. The rest of my bulbs I haven't kept up with but those 2 older ones looked very distinctive with aluminum heatsink material for their bottom halves.

Killer of LED bulbs is heat. If you have some in fixtures that trap heat you should either replace the fixtures or get high quality bulbs for those fixtures. Look for bulbs rated for hot locations. And for outdoors make sure it's rated for wet areas.