Linux

https://www.golinuxcloud.com/mount-partition-using-systemd/#Steps_to_mount_partition_using_systemd_unit_file

#cat /etc/systemd/system/mnt-data.mount
[Unit]
Description=nfs mount script

[Mount]
What=192.168.0.30:/mnt/tank/Media
Where=/mnt/data
Type=nfs4

[Install]
WantedBy=remote-fs.target

The file name has to match the folder upon which the share is mounted with hypens instead of forward slashes

Having something rm your entire NAS is an emergency, not something that should be happening regularly. If it is, you've got bigger problems.

If you want the lowest latency, you could try NBD. It's a block protocol but with less overhead compared to iSCSI. https://github.com/NetworkBlockDevice/nbd/tree/master

Like iSCSI, it exposes a disk image file, or a raw partition if you'd like (by using something like /dev/sda3 or /dev/mapper/foo as the file name). Unlike iSCSI, it's a fairly basic protocol (the API is literally only 9 commands). iSCSI is essentially just regular SCSI over the network.

NFS and SMB have to deal with file locks, multiple readers and writers concurrently accessing the same file, permissions, etc. That can add a little bit of overhead. With iSCSI and NBD, it assumes only one client is using the file (because it's impossible for two clients to use the same disk image at the same time - it'll get corrupted) and it's just reading and writing raw data.

main thing to note is that NFS is an object based storage (acts like a share) where iSCSI is block based (acts like a disk). You'd really only use iSCSI for things like VM disks, 1:1 storage, etc. For home use cases unless you're selfhosting (and probably even then) you're likely gonna be better off with NFS.

if you were to do iSCSI I would recommend its own VLAN. NFS technically should be isolated too, but I currently run NFS over my main VLAN, so do what ya gotta do

idmapping

idmap only works with Kerberos auth, but iirc I didn't have to set anything up specifically for it. Though I've also never really had to test it since my UIDs match coincidentally, I just tested with the nfsidmap command.

Well, with multiple users you'd need to decide what the use case is for the whole NAS and then work down from there.

Are you sharing everything in the NAS with everyone? In that case your NAS setup is fine, just a little permissive, because with RW to everything, the end users can break everything.

If it were me setting this up, I'd have different mount points for different users. 1 mount for each user that only they can read/write (not even you should be able to see it), and 1 mount that everyone can read/write, maybe if you want to go a little bonkers, 1 mount that everyone can read, but only you can write to.

Then you'd mount those three to separate mounts in your /media, and you can link them from your home directory for specific use cases.

Obviously this is completely overkill, but you can take the parts that sound appealing to you and ignore the rest.

I set up the mount points in configuration as dynamic NFS volumes and added Bookmarks to nautilus. You can get to the volume either with cd command or right-click -> terminal here. You can shut down the NAS and only lose the share, which returns when the system goes online.

This is much better than WbDAV, which is fine for simple sharing or for devices that can't handle NFS easily like Android phones.

There aren't many options... you can either modify the share or you cannot. 🙂 Pick one.

Well, for one, it's network attached storage. If it's not present in the network for one reason or another, guess what, your OS doesn't boot... or it errors during boot, depending on how the kernel was compiled and what switches your bootloader sends to the kernel during boot. Second, this is an easy way for malware to spread, especially if it's set to run after user logon.

If I mount it in the file manager, how do I reference that location in the terminal to say do copy operations to it?

I've found that Dolphin, at least, is much slower with network mounts than a CLI-based "mount".