nosnahc

I don't know if it the better place to ask my question and if it's not I apologize...

I am a biker and despite my love for FOSS applications, I cannot deny that Waze is very practical (especially for speed camera signaling). I use CalyxOS and there is a feature that makes it easy to use the work profile. On the other hand, I do not know how useful it is to limit my data transmission to Google. Is this really usefull? (I also have TrackerControl, but if I block anything, Waze no longer works)

I actually have Marlin + Octoprint but found out recently that Klipper exist. I read everywhere that Klipper is better but I don't really get why. I understand that Klipper use raspberry as powerfull calculator instead of the STM32 of the printer, but octoprint is used to send Gcode to Marlin too... So what's the really difference please?

Edit : I don't understand how Klipper or Marlin can give better results when gcode and instructions are generated by Cura

Bring my buddy at work

How is this possible even with abl? I dont' get it...

Hi everyone, just to put some content in this community, I thought that sharing my setup could be useful to some people!

I have a Creality Ender 3-S1 Plus as my first printer. Why this choice? because... I wanted a big set, it suited my budget, and... I didn't know too much about it so I followed my instinct.

First thing I did was to replace the original firmware with this one. Many more features including a lot of work on the touch screen, and more compatibility with Octoprint (see below).

I then installed a led strip with a support printed by me.

Then Tasmota connected sockets (open source firmware). Driven by Octoprint, I can turn on my printer remotely, then the LED strip and the printers will be turned off automatically at the end of printing. Open-source was important to me, for control to be done locally only, and not via a server on the other side of the world..

I then discovered via Reddit (urg) the existence of Octoprint. After trying to install it on my first generation RPi, I bought an RPi 4 and created myself an optimized server.

I added some plugins including:

• Bed visualizer: to have a 3D visual of the bedleveling
• OctoEverywhere! (in free version) to have access to my server outside my local network (at work for example)
• Signal Notifier: to send me a message on Signal (I hate Meta and therefore Whatsapp) when the print is finished
• Tasmota: to control my connected sockets, very easy to use by adding commands in my Gcode
• UI Customizer: to have a beautiful interface
• Slicer Thumbnails: to have a preview of the Gcode rather than just the name (requires manipulation in Cura)
• M73 progress: to display the printing progress on the touch screen

To perfect my installation and avoid going back and forth to check my impressions, I installed a Logitech HD C270 with a custom case.

Here, to conclude, I had a lot of trouble with Signal to install it on the RPi but I created a script to achieve this easily. And I burned my first bed by putting a Z-offset too low so I bought another one on amazon which I am very satisfied with.

My next project will be to confine my printer to print ABS.

Edit : (Yes, I need to clean the bed)

Edit 2 : Here's the video to not burn your bed, watch it until the end!

Bonjour à tous, Je viens vers vous car j'ai un petit souci avec Lemmy. Je voudrais faire un très gros post sur 3Dprinting et y poster plusieurs photos avec, mais je n'arrive à intégrer qu'une photo. Quelqu'un s'aurait comment faire svp?

Just want to share one of my prints. Printer in Ender 3-S1 plus. Painted with Posca pens

Smoother in reality than the picture

Spez qui passe un mauvais moment sur le côté français de r/place!

Par pure curiosité je suis allé voir sur Reddit... Et tout à l'air normal j'ai bien l'impression !

Surtout sur le r/france qui se porte à merveille.

Ça me fait toujours sourire de voir tout le monde râler contre le capitalisme, le monopole et j'en passe. Mais personne n'est vraiment prêt à changer ses habitudes...

Ca me fait penser au scandale Whatsapp où peu de gens ont changés leurs habitudes pour Signal ou autre appli.

Finalement presque tout le monde finit par accepter la grosse pilule...